ISI Certification (BIS) for POLYPROPYLENE (PP) MATERIALS FOR MOULDING AND EXTRUSION IS 10951

BIS Certification for Polypropylene (PP) Materials For Moulding And Extrusion as per IS 10951

ISI Certification (BIS) for POLYPROPYLENE (PP) MATERIALS FOR MOULDING AND EXTRUSION IS 10951

Category: ISI Certification (BIS)

BIS CERTIFICATION FOR POLYPROPYLENE (PP) MATERIALS FOR MOULDING AND EXTRUSION as per IS 10951

1. Introduction to Indian Standard IS 10951; Polypropylene (PP) Materials For Moulding And Extrusion – Step Bolts for Steel Structures

IS 10951 cover Polypropylene (PP) MaterialsfFor Moulding and Extrusion. This standard specifies the manufacturing, chemical and physical requirements and testing of Polypropylene (PP) Materials for Moulding and Extrusion.
IS 10951 specifies the quality parameters or characteristics of the Polypropylene (PP) Materials For Moulding And Extrusion as follows

Melt Mass Flow Rate
Flexural Modules
Izod Impact Test
Tensile Yield Strength
Elongation at Yield
Tensile Strength at Break
Elongation at break
Charpy Impact strength
Hardness
Melting Temperature
Temperature of deflection
Flammability
Ignitability
Dissipation factor
Volume Resistivity
Surface Resistivity
Dielectric Strength
Water absorption
Density

2. Mandate for ISI Mark Certification of Polypropylene (PP) Materials For Moulding And Extrusion (IS 10951) :

Under section 14 of Bureau of Indian Standards Act, 1986 (63 of 1986), the Ministry of Commerce and Industry, Department for Promotion of Industry and Internal Trade after consulting the Bureau of Indian Standards has issued the Quality control order.
As per the Quality control order, all the manufacturers of Polypropylene (PP) Materials for Moulding and Extrusion are obligated to obtain ISI Mark Certification.

3. Types of Polypropylene (PP) Materials For Moulding And Extrusion covered under IS

“Licence is granted to use Standard Mark on Polypropylene (PP) Materials for Moulding and Extrusion as per IS 10951:2020”.
Types / Scope of license	Designation – As per Clause 3 of IS 10951 Additional Requirements - With/Without Additional requirement for product used in contact with Food stuff, Pharmaceuticals and drinking water

4. Procedure to obtain BIS Certification of Polypropylene (PP) Materials For Moulding And Extrusion to use ISI mark as per IS 10951

For Indian Manufacturers (Standard Timeframe – 30 days) click here
For Foreign Manufacturers (Standard Timeframe – 180 days)click here

5. Requisites to get the BIS license for Polypropylene (PP) Materials For Moulding And Extrusion

Conformity of Raw Material as per IS 10951
In-house testing laboratory for mandatory tests
Competent Quality Control Personnel
Adherence to the BIS guidelines for Polypropylene (PP) Materials for Moulding And Extrusion as per Indian standard IS 10951
There are 3 major categories of document required to get the BIS license:

Administrative Details
Technical Details
Quality Control Personnel Details
Commercial Details

6. Expenses involved in obtaining BIS certificate for Polypropylene (PP) Materials For Moulding And Extrusion as per IS 10951 under the Product Certification (Scheme-I) of BIS :

For Indian Manufacturers
No.	Major Charges		Amount	Remark
1.	BIS Fee	Application Fees	INR 1000	To be paid in BIS A/c directly. 20% rebate on Marking Fee for MSME units.
		Audit Charges	INR 7000
		License Fee	INR 1000
		Marking Fee	INR 120,000
2.	Testing Charges	Sample Test Fee	As Applicable	To be paid into BIS approved Lab A/c
3.	ERCS Service Fee	Consultancy & others	As per actual, (Depending upon the product and the region of factory)

For the Foreign Manufacturers
No.	Major Charges	Particulars	Amount	Remark
1.	BIS Fee	Application Fees	USD 30	To be paid into BIS A/c directly in USD (SWIFT). SAARC countries can pay in INR with GST@18%
		Audit Charges (consolidated)	USD 3200 to USD 5900
		License Fee	USD 30
		Marking Fee	USD 1500
2.	Testing Charges	Sample Test Fee	As Applicable	To be paid into BIS approved Lab A/c
3.	ERCS Service Fee	Consultancy & others	As per actual, (Depending upon the product and the region of factory)

In the certification process, product testing is the most important stage as it determines whether the quality of the product meets Indian standards.
For the same purpose, investments in testing facilities are required to install test equipment for internal factory test laboratories.
Apart from charges mentioned above in the table, we may ask you to pay/reimbursement for a Pre-Visit at your Factory Premises to ensure the conformity of your product as per the relevant Indian Standard & BIS guidelines for its BIS certification.

7. Role of ERCS Private Limited in getting your product certified :

To get BIS certification and produce a standard quality product, the manufacturer must ensure that their product must follow the specified Indian Standard Specifications (ISS) which we directly interpret to you from the BIS officials as per the Indian Standards.
ECRS Private Limited will be your friend, philosopher and guide in the whole process of getting your product certified by the concerned authorities/ departments.
Scope of work by ECRS Private Limited:

Ensuring the conformity of your product as per IS 10951:

ERCS Pvt. Ltd. has developed a vast network within the Plastic Industry & various BIS departments to assist for ensuring conformity of the product Polypropylene (PP) Materials for Moulding and Extrusion according to according to IS 10951.

Effective documentation with the awareness of the BIS guidelines:

In order to facilitate the manufacturing industry in obtaining BIS certifications, guidelines have been developed. Our team has the experience of completing over 150 projects and technically competent acquaintances in various Industries.

We are familiar with the Indian Standard Specifications & BIS guidelines and deliver the most suitable interpretation to the Quality Control Personnel so we can do a reliable and effective documentation of your product in accordance with the BIS guidelines.

A pre-visit can be paid at your factory premises:

In the process of getting BIS certification, the officer from BIS authority visits the factory for inspection. In order to get good results, the BIS inspection should go smoothly without any Non-Conformity. By keeping this goal in mind, our team will organize a pre-visit to your factory premises so that required changes can be adapted so as to remove the elements of fallibility.

Assistance for BIS audits:

We will explain the whole procedure of conducting a BIS inspection and make you aware of the things which need to be prepared and readily available at the time of inspection.

Benefits of getting ISI Mark for Polypropylene (PP) Materials for Moulding and Extrusion to sell in Indian Market with our help

The term “ISI mark" means, that a certain product conforms to the quality standards set up by the government.
It is compulsory for Polypropylene (PP) Materials for Moulding and Extrusion to obtain the ISI Mark and the violators are penalized with the material seize and a significant sum as fine.
Getting certification improves the probability of your product to survive and compete in the market.
Customers have the tendency of buying ISI certified products as it ensured safety and standard quality. Hence, with the certified products you can win the confidence and trust of the buyer.
With the word of mouth of such client list, you can establish your credibility in the market.
Hence with the renowned brand, you can raise the standard and benchmark the market value of the product.

(0)

BIS (Bureau of Indian Standards)

Waste Management Compliances

Other Regulatory Compliances