BIS Certification for
Geotextiles for Permanent Erosion Control in Hard Armor Systems IS 16392

Hard Armor is a term used to describe permanent stabilization solutions, which exist in many forms, both vegetated and non-vegetated. Erosion protection structures or armour systems dissipate the hydraulic forces that cause erosion, and they preserve the subgrade soil or fill soil behind it. Geotextiles provide separation, stabilization and filtration between the subgrade soil and the rip-rap, gabions or pre-cast blocks to prevent piping and erosion of fine soil particles while allowing the free passage of water.  Introduction to Indian Standard IS 16392 Geotextiles for Permanent Erosion Control in Hard Armor Systems.

 

IS 16392 covers Geotextiles for Permanent Erosion Control in Hard Armour Systems. This standard covers general and performance requirements for geotextiles used between energy absorbing armor systems and the in-situ soil to prevent soil loss resulting in excessive scour and to prevent hydraulic uplift pressures causing instability of the permanent erosion control system. This standard does not apply to other types of geosynthetic erosion control materials such as turf reinforcement mats. Woven slit film geotextiles, that is, geotextiles made from yarns of a flat, tape-like character, shall not be used for permanent erosion control applications

 

Specification of  IS 16392

IS 16392 specifies the quality parameters or characteristics of the  Geotextiles for Permanent Erosion Control in Hard Armour Systems as follows :

(i)           Type of Geotextile

(ii)         Roll Length

(iii)        Roll Width

(iv)        Grab Strength

(v)          Sewn Seam Strength

(vi)        Trapezoidal Tear Strength

(vii)       CBR Puncture Strength

(viii)     Burst Strength

(ix)        Permittivity

(x)          Apparent Opening Size

(xi)        Durability Properties

(xii)       Packing

 

Mandate for ISI Mark Certification of Geotextiles for Permanent Erosion Control in Hard Armor Systems (IS 16392:2015)

In exercise of the powers conferred by sub-sections (1) and (2) of section 16 read with section 17 and sub-section (3) of section 25 of the Bureau of Indian Standards Act, 2016 (11 of 2016), the Central Government is of the opinion that it is necessary so to do in the public interest and after consulting the Bureau of Indian Standards, hereby makes the following Order, namel Geo Textiles (Quality Control) Order, 2022. As per the Geo Textiles (Quality control) order, all the manufacturers of Geotextiles for Permanent Erosion Control in Hard Armor Systems are obligated to obtain ISI Mark Certification.

 

Procedure to obtain BIS Certification of  Geotextiles for Permanent Erosion Control in Hard Armor Systems

To Check the  Procedure in Detail, Please Visit:

Process of ISI Certification for Indian Manufacturers (BIS Certification India)

Process of ISI Certification for Foreign Manufacturers (FMCS License)

 

Requirements to get the BIS license for  Geotextiles for Permanent Erosion Control in Hard Armor Systems

• Conformity of Raw Material as per IS 16392:2015
•  In-house testing laboratory for mandatory tests
• Competent Quality Control Personnel
• Adherence to the BIS guidelines for  Geotextiles for Permanent Erosion Control in Hard Armor Systems as per Indian standard IS 16392:2015
• There are 3 major categories of document required to get the BIS license:

a.   Administrative Details

b.   Technical Details

c.    Quality Control Personnel Details

d.   Commercial Details

 

Cost of ISI Certification for IS 16392

Expenses involved in obtaining BIS certificate for  Geotextiles for Permanent Erosion Control in Hard Armor Systems as per IS 16392:2015under the Product Certification (Scheme-I) of BIS :

S No.	Particular	Amount (INR)	Remarks
1.	Application Fee	1000	To be paid directly to BIS
2.	Audit Fee	7000	To be paid directly to BIS
3.	License Fee	1000	To be paid directly to BIS
4.	Sample Testing Fee	As Applicable	To be paid directly to BIS (Testing charges vary from product to product and lab to lab.)
5.	Minimum Advance Marking Fee	As per actual	To be paid directly to BIS (Marking fee varies as per Indian Standard)
6.	Renewal Fee	1000	To be paid directly to BIS
7.	Inclusion Fee	5000	To be paid directly to BIS
8.	ERCS Pvt Ltd Service Fee	Please contact info@elitasrcs.com
	Remarks	Including all the taxes

• In the certification process, product testing is the most important stage as it determines whether the quality of the product meets Indian standards.
• For the same purpose, investments in testing facilities are required to install test equipment for internal factory test laboratories.
• Apart from charges mentioned above in the table, we may ask you to pay/reimbursement for a Pre-Visit at your Factory Premises to ensure the conformity of your product as per the relevant Indian Standard & BIS guidelines for its BIS certification.

 

Role of ERCS Private Limited in getting your product certified :

To get BIS certification and produce a standard quality product, the manufacturer must ensure that their product must follow the specified Indian Standard Specifications (ISS) which we directly interpret to you from the BIS officials as per the Indian Standards. ERCS Private Limited will be your friend, philosopher and guide in the whole process of getting your product certified by the concerned authorities/ departments.

 

Scope of work by ECRS Private Limited:

a.     Ensuring the conformity of your product as per IS 16392:2015:

ERCS Pvt. Ltd. has developed a vast network within the Geotextile Industry & various BIS departments to assist for ensuring conformity of the product  Geotextiles for Permanent Erosion Control in Hard Armor Systems according to according to IS 16392:2015.

b.     Effective documentation with the awareness of the BIS guidelines:

In order to facilitate the manufacturing industry in obtaining BIS certifications, guidelines have been developed. Our team has the experience of completing over 150 projects and technically competent acquaintances in various Industries.

We are familiar with the Indian Standard Specifications & BIS guidelines and deliver the most suitable interpretation to the Quality Control Personnel so we can do a reliable and effective documentation of your product in accordance with the BIS guidelines.

c.      A pre-visit can be paid at your factory premises:

In the process of getting BIS certification, the officer from BIS authority visits the factory for inspection. In order to get good results, the BIS inspection should go smoothly without any Non-Conformity. By keeping this goal in mind, our team will organize a pre-visit to your factory premises so that required changes can be adapted so as to remove the elements of fallibility.

d.     Assistance for BIS audits:

We will explain the whole procedure of conducting a BIS inspection and make you aware of the things which need to be prepared and readily available at the time of inspection.

 

BIS Certificate Benefits for  IS 16392

Benefits of getting ISI Mark for  Geotextiles for Permanent Erosion Control in Hard Armor Systems to sell in Indian Market with our help

• The term “ISI mark" means, that a certain product conforms to the quality standards set up by the government.
• It is compulsory for  Geotextiles for Permanent Erosion Control in Hard Armor Systems to obtain the ISI Mark and the violators are penalized with the material seize and a significant sum as fine.
• Getting certification improves the probability of your product to survive and compete in the market.
• Customers have the tendency of buying ISI certified products as it ensured safety and standard quality. Hence, with the certified products you can win the confidence and trust of the buyer.
• With the word of mouth of such client list, you can establish your credibility in the market.
• Hence with the renowned brand, you can raise the standard and benchmark the market value of the product.